Industrial battery chargers

PFC power stage

PFC stage is required to shape the input current of the power supply and to meet the power factor and current THD norms such as IEC61000-2-3. In addition, the PFC stage also enhances system performance by reducing RMS input current, facilitating power supply holdup and improving efficiency of downstream converters.

Products

Power factor correction (PFC) controllers

UCC28070—Two-phase Interleaved continuous conduction mode (CCM) PFC controller

UCC28180—18-kHz-250-kHz CCM PFC controller with enhanced startup & transient response

UCC28065—Natural Interleaving™ transition-mode PFC controller with high-frequency switching

UCC28051—Transition mode PFC controller with 12.5V/9.7V UVLO and IEC61000-3-2 compliance, -40°C to 105

UCC28056—6-pin high performance CRM/DCM PFC controller

Digital power isolated controllers

UCD3138A—UCD3138A Highly Integrated Digital Controller for Isolated Power

Isolated gate drivers

UCC21551-Q1—Automotive, 4A/6A 5kVRMS dual-channel isolated gate driver with EN and DT pins for IGBT and SiC

UCC21540—5.7kVrms 4A/6A dual-channel isolated gate driver with dual inputs, DT pin & 8V UVLO in DW or DWK pkg

UCC5350—3kVrms, 5A/5A single-channel isolated gate driver with miller clamp or split out & 8V or 12V UVLO

UCC5320—3k/5kVrms, 2A/2A single-channel isolated gate driver with UVLO referenced to GND or split output

Gallium nitride (GaN) ICs

LMG3616—650-V 270-mΩ GaN FET with integrated driver and protection

LMG3622—650V 120mΩ GaN FET with integrated driver, protection and current sensing

LMG3522R030-Q1—Automotive 650-V 30-mΩ GaN FET with integrated driver, protection and temperature reporting

LMG3410R070—600-V 70mΩ GaN with integrated driver and protection

Half-bridge drivers

UCC27714—4-A, 600-V half bridge gate driver

LMG1210—1.5-A, 3-A, 200-V half bridge gate driver, 5-V UVLO and programmable dead-time for GaNFET and MOSFET

LM5108—2.6-A, 110-V half bridge gate driver with enable and interlock

UCC27712—1.8-A/2.8-A, 620V half bridge driver with interlock

Low-side drivers

UCC27517—4-A/4-A single-channel gate driver with 5-V UVLO and 13-ns prop delay in SOT-23 package

UCC27524—5-A/5-A dual-channel gate driver with 5-V UVLO, enable, and 1-ns delay Matching

UCC27324—Non-inverting 4-A/4-A dual-channel low side gate driver

UCC27424—4-A/4-A dual-channel gate driver with enable and 5-V IN handling

N-channel MOSFETs

CSD18511Q5A—40-V, N channel NexFET™ power MOSFET, single SON 5 mm x 6 mm, 2.3 mOhm

CSD18510Q5B—40-V, N channel NexFET™ power MOSFET, single SON 5 mm x 6 mm, 0.96 mOhm

CSD13381F4—12-V, N channel NexFET™ power MOSFET, single LGA 1 mm x 0.6mm, 180 mOhm, gate ESD protection

General-purpose op amps

TLV9102—Dual, 16-V, 1.1-MHz, low-power operational amplifier

TL103WB—Dual, 36-V 1.2-MHz low-offset-voltage operational amplifier with internal reference

TLV9002-Q1—Automotive-grade, dual, 5.5-V, 1-MHz, RRIO operational amplifier for cost-optimized applications

Analog current-sense amplifiers

INA296B—-5-V to 110-V, bidirectional, 1.1-MHz 8-V/µs high-precision current sense amplifier

INA280—2.7-V to 120-V, 1.1-MHz, high-precision current sense amplifier in small (SC-70) package

INA181—26-V bi-directional 350-kHz current-sense amplifier

INA180—26V, 350kHz current sense amplifier

Comparators

LM393B—Dual commercial grade standard comparator

LM393LV—'1.65-V to 5.5-V, low-voltage dual commodity comparator

TLV1701—Single high voltage, low power comparator

TL331—High Voltage Single Differential Comparator

Precision op amps (Vos<1mV)

OPA2197—Dual 36-V, precision, rail-to-rail input output, low offset voltage op amp

OPA2209—Dual, 2.2-nV/rtHz, 18-MHz, precision, RRO, 36-V operational amplifier

OPA197—Single, 36-V, precision, rail-to-rail input output, low offset voltage op amp

TLV8811—Single 425-nA precision nanopower operational amplifier for cost-optimized systems

Digital temperature sensors

TMP1826—1-Wire® ±0.2°C accurate digital temperature sensor with 2-kbit EEPROM

TMP102—2C digital temperature sensor, I2C/SMBus in 2.56mm2 package

LMT01—0.5°C Accurate 2-pin Temperature Sensor with a Pulse Train Interface

Isolated DC/DC power stage

The isolated DC/DC power stage converts the boosted DC voltage at the PFC output into an isolated low voltage CC/CV controlled output required for charging the battery. Efficiency is a key parameter for this stage as it needs to contain protection mechanisms for over current and over temperature.

Products

Digital temperature sensors

TMP1826—1-Wire® ±0.2°C accurate digital temperature sensor with 2-kbit EEPROM

TMP102—2C digital temperature sensor, I2C/SMBus in 2.56mm2 package

LMT01—0.5°C Accurate 2-pin Temperature Sensor with a Pulse Train Interface

Transformer drivers

SN6505A—Low-noise, 1-A, 160-kHz transformer driver with soft start for isolated power supplies

SN6505B—Low-noise, 1-A, 420-kHz transformer driver with soft start for isolated power supplies

SN6501—Low-noise, 350-mA, 410-kHz transformer driver for isolated power supplies

Reverse battery protection

This subsystem implements the battery reverse polarity protection, and is responsible for preventing any damage to the board if the battery is accidentally connected in reverse

Products

N-channel MOSFETs

CSD18511Q5A—40-V, N channel NexFET™ power MOSFET, single SON 5 mm x 6 mm, 2.3 mOhm

CSD18510Q5B—40-V, N channel NexFET™ power MOSFET, single SON 5 mm x 6 mm, 0.96 mOhm

CSD13381F4—12-V, N channel NexFET™ power MOSFET, single LGA 1 mm x 0.6mm, 180 mOhm, gate ESD protection

CSD18532Q5B—60-V, N channel NexFET™ power MOSFET, single SON 5 mm x 6 mm, 3.2 mOhm

NAND gates

SN74HCS00—4-ch, 2-input, 2-V to 6-V low power NAND gates with Schmitt-trigger inputs

SN74LVC1G132—Single 2-input, 1.65-V to 5.5-V NAND gate with Schmitt-Trigger inputs

AND gates

SN74AHC1G08—1-ch, 2-input 2-V to 5.5-V high-speed (9 ns) AND gate

SN74LVC1G08—1-ch, 2-input 1.65-V to 5.5-V 32 mA drive strength AND gate

SN74AHC08—4-ch, 2-input 2-V to 5.5-V high-speed (9 ns) AND gate

Noninverting buffers & drivers

SN74LVC2G34—2-ch, 1.65-V to 5.5-V buffers

SN74LV541A—Eight-channel, 2-V to 5.5-V buffers with tri-state outputs

SN74LVC1G125—Single 1.65-V to 5.5-V buffer with 3-state outputs

OR gates

SN74LVC1G32—1-ch, 2-input 1.65-V to 5.5-V 32-mA drive strength OR gate

Signal isolation stage

This subsystem transfers sense and control signals across the primary to secondary isolation barrier. It can be implemented using digital isolators, isolated amplifiers and optocouplers

Products

Isolated amplifiers

AMC1300B-Q1—Automotive, ±250-mV input, precision current sensing reinforced isolated amplifier

AMC1311-Q1—Automotive, 2-V input, precision voltage sensing reinforced isolated amplifier

AMC1300—±250-mV input, precision current sensing reinforced isolated amplifier

AMC1200—±250-mV input, precision current sensing basic isolated amplifier

Digital isolators

ISO6762—General purpose, 50-Mbps, six-channel (4/2) digital isolator

ISO7742-Q1—Automotive, robust EMC, quad-channel, 2/2, reinforced digital isolator

ISO7742—Robust EMC, quad-channel, 2/2, reinforced digital isolator

ISO6721—General-purpose, dual-channel, 1/1 digital isolator

Digital power isolated controllers

UCD3138A—UCD3138A Highly Integrated Digital Controller for Isolated Power

Wired interface

Wired communication features like CAN, RS485, PMBus monitor and control the end equipment. The communication interface can either be isolated or non-isolated and can have a protocol stack execute on the host MCU.

Products

Isolated RS-485 transceivers

ISO1410—EMC protected, 500-Kbps, half-duplex, 5-kVrms isolated RS-485 & RS-422 transceiver

ISO1412—EMC protected, 500-Kbps, full-duplex, 5-kVrms isolated RS-485 & RS-422 transceiver

ISO3082—200-Kbps, half-duplex, 2.5-kVrms isolated RS-485 & RS-422 transceiver

ISO3080—200-Kbps, full-duplex, 2.5-kVrms isolated RS-485 & RS-422 transceiver

Isolated CAN transceivers

ISO1044—Isolated CAN FD transceiver in small package

ISO1050—Isolated 5-V CAN transceiver

Digital isolators

ISO6762—General purpose, 50-Mbps, six-channel (4/2) digital isolator

ISO7742-Q1—Automotive, robust EMC, quad-channel, 2/2, reinforced digital isolator

ISO7742—Robust EMC, quad-channel, 2/2, reinforced digital isolator

ISO6721—General-purpose, dual-channel, 1/1 digital isolator

I2C isolators

ISO1541—2.5-kVrms, isolated unidirectional clock, bidirectional I2C isolator

RS-485 & RS-422 transceivers

THVD1410—3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection

THVD1520—5-V RS-485 transceiver up to 10 Mbps with ±8-kV IEC ESD protection

SN65HVD70—3.3V, Full-Duplex RS-485, 12kV IEC ESD, 400kbps data rate, w/Enables

ESD protection diodes

ESD2CAN24-Q1—Automotive, dual, 3-pF, ±24-V, ±30-kV ESD protection diode for in-vehicle networks

TPD4E05U06—Quad 0.5-pF, 5.5-V, ±12-kV ESD protection diode for USB, HDMI & High Speed Interfaces

TPD1E05U06—0.5-pF, 5.5-V, ±12-kV ESD protection diode in 0402 package for High Speed Interfaces

TPD1E10B06—12-pF, ±5.5V, ±30-kV ESD protection diode in 0402 and SOD-523 package

Application-specific port protection ICs

TPD6S300A—USB Type-C® port protector: short-to-VBUS overvoltage and 6ch ESD protection with improved OVP

RS-232 transceivers

MAX3221—3- to 5.5-V single channel 250kbps RS-232 line driver/receiver with +/-15-kV ESD protection

Digital power isolated controllers

UCD3138A—UCD3138A Highly Integrated Digital Controller for Isolated Power